Mobile Auto Starter/Auto Switch(Three Phase)

(1) When dryrun occurs then after settled time motor will be started automatically.

(2) After dryrun, if supply goes for some time and then arrives, motor will be started automatically.

(3) After dryrun motor will not start automatically until you do not give turn ON command.

 *Timer Mode:*

(1) We can keep motor turned ON for specific time. 

e.g. 1 min, 2 min, .... 24 Hrs.

(2) We can keep motor turned ON according to clock time.

e.g. 02:00AM - 03:00AM

        This is repeating timer. Do not required to set daily.

(3) Cyclic timer can be settled from 1 min to 24 Hrs with both ON and OFF time.

e.g. motor ON for 10 min and OFF for 1 Hr, again 10 min ON and 1 Hr OFF this cycle repeats continuously.

(4) After supply resumption in how many time motor should be turned ON, this time can be varied from 1 min to 2:30 Hr.

(5) All timers can be turned off.

 *Voltage Setting:*

You can set at how many voltage motor should start.

 *Connection Fault:*

If there is connection fault like broken cable, overloaded relay or wrong wiring then you will get alert at time of turning ON of motor.

 *Alerts:*

"AKMOS Mobile Auto Switch" really talks to you.

If anyone starts motor by hand using starter button then you will get alert.

You can set that after supply resumption motor should started automatically or without turning on just give alert.

After fuse insertion, supply resumption, motor turning ON or OFF you will get alert via call/SMS.

After turning ON motor you will get alert that how many current is drawing motor.

You will get notification of last time how many time motor was run.

All alerts will be sent to last dialer number from maximum 9 registered user's number's.

You can choose alert type Call or SMS.

You can turn ON or OFF all alerts individually.

 *Truecaller:*

Motor should be started from only registered numbers or from any number it's your choice.

 *Balance:*

In mobile auto's SIM card how many talktime is remaining this can be checked from your mobile.If there is zero balance in mobile auto's SIM card then also auto works normally.

 *Security:*

If your AKMOS Mobile Auto is stolen then don't worry, In this device tracker and cell location feature is available. So you can check device's location by sending command or if anyone changes SIM card of device then you will get alert from that new number. By using this number and location you can easily find out thieve.

After theft if you informs to AKMOS then that stolen device will be blocked and it will be useless for thieve.

 *Battery Backup*

For communicating with device in absence of electricity there is option to attach battery.

 *Guarantee:*

 For any difficulty in product in 1 year, you will get new device in replace of old one and after 1 year same device will be repaired and you will have to pay repairing charges.

New update in Acmos

Timer update
Phase failure time recovery : Suppose the motor running time is set for 4 hours and if the light goes off after only 3 hours of motor running then when the light comes on the motor will run again for the remaining 1 hour.
Multi Slot Timer: Suppose the motor is to be switched on once during the day from 7 am to 8 am, again from 2 pm to 03:30 pm, again from 10 pm to 11 pm, timers can be set in maximum 5 slots.
Timer operation without battery
All timers will work with 1 minute accuracy even without battery device.

On/off period
How many times the motor has been running, 
The message will automatically show how long the motor was running when it was finally switched off, the total time the motor was running since the mobile auto switch was switched on.

On/off time update
Both motor start date and time and shutdown date and time can be viewed in the motor detail status message.

Drain/overload setting update
Drainage/overload current can be set differently for both 3 phase mode and 2 phase mode where a changeover is installed to run a 3 phase motor on 2 phase. Drought/overload will be set automatically no need to message. If the ampere setting is to be changed, it can be changed by message.

Motor current
Motor detail status messages will display motor current accurate to one decimal point.

Line fault detect time
In many places where there is a hook or loose connection, even if the supply is not good for half a second, the motor does not start automatically in the earlier model. That will not happen in the new update.

Application update
All the updated timers can be set from the updated application. The application can be downloaded from Play Store.

Language update
The model is currently available in the following languages.
Marathi, Hindi, English, Tamil, Telugu, Kannada, Gujarati, Bengali

Hardware update
In this earlier model, resettable fuses were placed inside the device, some of the fuses were blown or the IC malfunctioned during lightning flash or sudden high voltage, to prevent these faults from occurring, glass fuses are provided on the wire, outside of the device in the new model. So in case of high voltage or flash of lightning, those glass fuses will only blow and possibly no damage will occur inside the machine. If the old glass fuse is taken from the local market, the device will start again, no need to open it from the place or send it to the company.